YBA - GENESIS PH1 PHONO PREAMPLIFIER

The PH1 caters for MM, low output MC and high output MC cartridges. Never connect MM and MC cartridges at the same time as there will be a possibility with the high amplification factor that some noise could occur at the output stage. The selector control on the front panel of the PH1 has only two options(MM or MC) even though it accepts high output MC. The circuitry has been designed so that it will automatically sense which type of moving coil cartridge is being used and settings will adjust accordingly provided the correct selection is made from the toggle switch on the rear panel.
Звоните, чтобы узнать цену
Производитель: YBA
Вендор: audioclub
Бесплатная доставка
Дата доставки 7 ימי עסקים
+ -
מקבלים תשלום ב:


אשראי עד 12 תשלומים ללא ריבית.
יעוץ והכוונה מקצועית שירות והדרכה גם לאחר הקניה.
ליעוץ והזמנה טלפונית 03-5166919
 
משלוחים וזמני אספקה:

ניתן לאיסוף ממחסן ראשי ,הירקון 76 תל אביב- עד 3 ימי עסקים.
 
משלוח אקספרס עד הבית  לכל הארץ.
 
 

 

מוצרים מיבואן רשמי עם אחריות מלאה ומענה טלפוני, משלוחים מהירים לכל רחבי הארץ .

The power supply of the PH1 is provided by 10 NCR18650 batteries charged via a 24V power adaptor. The PH1 must be fully charged prior to use, a simple process with all necessary information clearly displayed. In full use conditions, the batteries can be charged up to 10,000 times with each full charge lasting for up to 8 hours.

Instructions for use are simple but need to be recognised as this product is battery driven. The PH1 needs to be fully charged before first use – it is a simple process clearly explained in the manual. Be aware that as long as the power adaptor is plugged in and switched on, then as the battery level drops during use, it will automatically recharge.  When not in use, disconnect the power adaptor and turn off the PH1 using the switch located on the underside of the unit. The PH1 should be regularly switched on and the power adaptor connected so that the battery level can be checked. If it is low, it should be recharged. If it remains on but not in use, then the batteries will discharge over time.

Yves-Bernard André has designed a specific moving coil transformer for use in the PH1. Because of its design, the YBA transformer is uniquely suited to meet the different characteristics of moving coil cartridges. It allows for the finest details of a reading to be highlighted at a very high level.

Product type

Phono Preamplifier

Cartridge impedance

3Ω to 100Ω

Output impedance

47kΩ

Bandwidth

10 HZ to150 KHZ

Gain

26 dB

Shielding full mu-metal

Double

Moving Magnet (MM)

Input impedance 47 kOhm 45dB Gain

Moving Coil (MC)

Input impedance 47 kOhm 50dB Gain

SNR

90dB (A weighted @ 40dB input gain)

THD

<0.005%

RIAA accuracy

Within 0.3dB/20Hz – 20kHz

Inputs

2 RCA Analog Signal Inputs

Outputs

1 RCA 1 Balanced

Display

OLED

Power Supply

10 pcs NCR18650 with 24V DC power adaptor

Color / Finish

Black aluminium with black acrylic panel

Dimensions (w x d x h)

215 x 335 x 115 mm

Weight

4 kg

The power supply of the PH1 is provided by 10 NCR18650 batteries charged via a 24V power adaptor. The PH1 must be fully charged prior to use, a simple process with all necessary information clearly displayed. In full use conditions, the batteries can be charged up to 10,000 times with each full charge lasting for up to 8 hours.

Instructions for use are simple but need to be recognised as this product is battery driven. The PH1 needs to be fully charged before first use – it is a simple process clearly explained in the manual. Be aware that as long as the power adaptor is plugged in and switched on, then as the battery level drops during use, it will automatically recharge.  When not in use, disconnect the power adaptor and turn off the PH1 using the switch located on the underside of the unit. The PH1 should be regularly switched on and the power adaptor connected so that the battery level can be checked. If it is low, it should be recharged. If it remains on but not in use, then the batteries will discharge over time.

Yves-Bernard André has designed a specific moving coil transformer for use in the PH1. Because of its design, the YBA transformer is uniquely suited to meet the different characteristics of moving coil cartridges. It allows for the finest details of a reading to be highlighted at a very high level.

Product type

Phono Preamplifier

Cartridge impedance

3Ω to 100Ω

Output impedance

47kΩ

Bandwidth

10 HZ to150 KHZ

Gain

26 dB

Shielding full mu-metal

Double

Moving Magnet (MM)

Input impedance 47 kOhm 45dB Gain

Moving Coil (MC)

Input impedance 47 kOhm 50dB Gain

SNR

90dB (A weighted @ 40dB input gain)

THD

<0.005%

RIAA accuracy

Within 0.3dB/20Hz – 20kHz

Inputs

2 RCA Analog Signal Inputs

Outputs

1 RCA 1 Balanced

Display

OLED

Power Supply

10 pcs NCR18650 with 24V DC power adaptor

Color / Finish

Black aluminium with black acrylic panel

Dimensions (w x d x h)

215 x 335 x 115 mm

Weight

4 kg

Ключевые слова